Project #7 Marble Machine #1

-

This post has long been the most viewed post on my entire blog but this design has long been superseded so I just want to make people aware that a better version exists 

 This kit is available for purchase through my shop https://msraynsford.ecwid.com/Laser-Cut-Marble-Machine-Kit-p95446965

I present to you my own hand cranked, laser cut marble machine. These are available to purchase as kits, for self assembly and I intend to run some local workshops for them too. The kit includes all the laser cut wooden parts, the nuts and bolts, and enough balls to fill the machine up and spares.


A long time ago in a blog not so far away (this one actually) I ran a project where I laser cut one item per day for 365 days. While I was making the machine triggers and before I'd committed to running my own Donkey Kong machine there was a suggestion that I should be making kits like this to sell on the day. I gave it a whirl and failed and if it couldn't be cut in a few days then it was a hindrance to the 365 project so it went on the back burner.

I recently picked it up again for two reasons, one it's a nice idea and makes a fun toy and secondly I need to investigate ball lifts for the eventual recreation of Donkey Kong. In the meantime Michael Henriksen from BustedBricks created this awesome, hand cranked, laser cut, marble machine, which is a great little kit too.
I don't want to steal his thunder or jump on his bandwagon so if you're only going to buy one kit, buy his, but if you're starting a collection of machines then buy mine aswell. (The price is similar for both machines)

7 projects/ 10 weeks




The main feature of this marble machine is the ring lift. Three stacked pieces of wood mean that the holes the balls are sat in are actually sloped. When the ball enters at the bottom it wants to stay inside the ring, as the ring is flipped upside down the slope is reversed and it wants to push the ball out of the ring. The balls then run down a 5 loop spiral and back into the bottom of the machine ready to go again. The machine holds 6 balls comfortably but a few more could be held in the lift at any given moment.

As you can see the balls are pretty free running and reliable. Putting multiple balls down the spiral too close together can cause a bit of a jam but I've left the handle small so it's a lot of effort to do that. The machine was designed tested with catapult ammo quality balls in mind (about 9.5mm wide) so cheap to replace should you lose any.




Pictured above is the evolution of the design in it's current form. Not being very successful before trying to design everything up front I took the approach of cutting and modifying parts as I went along. The process was much more fluid, got through far more material but probably averaged out on a cost/time basis.


The spiral needs a little bit of tweaking to make sure all the loops are equally spaced and free running. The initial transition from above the rails to alongside the rails is made easier by widening the track but it can still have a tendency to jump a loop. To this end only the top loop is fixed to the frame, the other loops are held apart by the frame but can be moved back and forward as required and then glued into place.

Popular posts from this blog

Wiring the Ruida Controller

-
Image
The RDC6442G controller from Ruida This is going to be quite an image heavy post describing the rewiring needed to convert between the Leetro controller and the Ruida controller. It is also pretty straight forward on the old Just Add Sharks laser cutters because all of the wires are clearly labelled. The controller was prepared in the previous step in order to make this conversion process as smooth as possible. The Leetro (Pad03) panel on the left and the Ruida panel on the right The view from inside the laser looking up at the control panel The control panel is an easy place to start, both panels have just a single cable that runs down to the controller, both panels are a very similar size, with the Ruida panel being slightly smaller underneath so it will fit in the hole left behind easily. The Pad03 panel clips into place so you'll need to reach up inside the machine to work the clips loose. The cable runs down the inside of the laser and is cable tied onto mounti
Read more

Rainbow Puzzle Box

-
Image
This is a binary sequence puzzle box built from 3mm birch plywood, it uses a Gray code pattern to ultimately align all the dials into a rainbow pattern before the lid can be removed. It's actually a redesign of a puzzle inside Loki's box of Tricks  because I thought it would make a cool stand alone puzzle box. The files are available for sale in my Etsy store . ( svg here ) The puzzle consists of five interlocking disks that can only rotate when the disks either side of it are in the correct position to allow it. The large wheel in the middle and the disks on the underside of the lid further restrict the rotation of the disks. The large wheel must be pointed to the disk that is being rotated and the large wheel is in turn restricted from pointing to the smaller disks depending on alignment. Once all the disks are aligned into the full rainbow the large wheel is completely free to rotate and can be turned to the edge of the box and allows the lid to be removed. There is a very
Read more

Laser Cut Cryptex

-
Image
This is my laser cut cryptex. It features 28 different characters and 9 rings, giving a total possible 10.5 Trillion different combinations. I took a bit of time developing the design so that I could add some nice features. This cryptex file is laid out so that you can have any number of rings in your own design. The best feature is that the codeword is changeable, each locking ring has an outer letter ring that can be placed in any one of the 28 different positions. Once the rings are back in place the ring locking bars can added and they prevent the rings from being modified until the box is open again. It's a bit hard to explain so I made a video showing how it all work ( svg here ) It took a long time to assemble this so I lived with my initial design choices but if I were to remake it I would adjust the file to make the ring locking bars out of 6mm ply and maybe put some blind holes onto the code rings to prevent the code being brute forced.
Read more